Foil & Strip

Silver Brazing Foil

  • Ultra-thin silver brazing foil for carbide and diamond segment brazing. Ag25, Ag45 grades available, custom thickness & width. Bulk wholesale from Yiwu Hexin Trading.
  • INQUIRY

Silver Brazing Foil: When the Joint Is a Surface, Not a Line

Wire and ring fillers are built for seams. Foil is built for faces. When two flat parts meet — a carbide insert on a steel body, a lid on a package, a laminate in a stack — a foil of the right thickness puts a uniform film of silver alloy across the entire interface, and the volume of that film is known to the tenth of a millimetre before the furnace door closes.

We produce silver brazing foil to customer drawings and agreed contract specifications: thickness from approximately 0.05 mm upward, widths and cut lengths to match your assembly, any silver content the application calls for, and packing designed to keep the foil flat, clean and ready to load.

Why Engineers Specify Foil Over Other Forms

  • Uniform coverage on planar joints. A foil sheet distributes alloy evenly across a face — something a wire, rod or ring cannot do on a flat interface.

  • Volume controlled by thickness. Alloy quantity is set by thickness × area. There is no operator variation, and no excess running into places it does not belong.

  • Stacking to build volume. Need more alloy on a wide gap? Lay two or three plies. The same thickness stock serves several joint designs, which simplifies stock-keeping.

  • Stamps into almost any outline. Foil is the raw material for shaped and blanked preforms — frames, discs, windows, annular pads — without the spring-back problems of wire.

  • Suited to furnace and vacuum brazing. Preloaded foil needs no hand feeding inside the furnace, which makes it the natural choice for batch and continuous atmosphere work.

Dimensions: Thickness Is the Design Variable

ParameterRange / Basis
Foil thicknessFrom approximately 0.05 mm upward, per contract specification
WidthCustom slit widths, agreed per drawing
Supply formatCoil rolls, cut-to-length sheets, stamped or blanked profiles
Silver content2% – 72% Ag, plus high-purity grades
Thickness toleranceAgreed in writing per order — the tolerance that matters is the one your joint was designed around
Surface conditionClean, oxide-free, free of rolling lubricant residue

Choosing the Thickness

Thickness sets the alloy volume per unit of joint area, so the starting question is always the joint, not the catalogue:

  • Close-fitting planar joints — thin foil fills the clearance without displacing the parts or starving the fillet.

  • Wider gaps or larger faces — thicker foil, or multiple plies, carries the extra volume the joint needs.

  • Laminated stacks — foil allows the alloy to be interleaved between layers so every interface receives filler at once.

  • Grinding allowance and post-machining — where the joint will be machined afterwards, account for the alloy that will be removed.

If the joint gap, face dimensions and heating method are known, the thickness decision usually takes one exchange of messages.

Alloy Grades for Foil

Silver-Copper Vacuum Grades (BAg-8 family, 72% Ag)

The Ag72Cu eutectic composition melts at a single temperature rather than across a melting range, and the analysis contains no high-vapour-pressure elements — the two properties that matter in vacuum furnaces and protective-atmosphere work. It is widely used on copper, nickel and their alloys, and on thin stainless assemblies in electronic and vacuum components.

Cadmium-Free Ag-Cu-Zn and Ag-Cu-Zn-Sn Grades

General-purpose joining of copper, brass, steel and stainless, with tin-bearing analyses lowering the working range and improving wetting on stainless. Available in silver contents from 2% to 56%, or to a customer-specified analysis under contract.

Special Analyses

Nickel-bearing grades for carbide tooling, layered constructions for thermal-expansion mismatch, and high-purity silver for applications with tight impurity limits. Compositions are produced to AWS A5.8 / A5.8M, ISO 17672 and GB/T 10046 designations, or to contract-specified analysis.

Considerations for Vacuum and Atmosphere Furnace Brazing

Foil used inside a furnace faces demands that wire on a bench never meets:

  • Low-vapour-pressure analysis. Elements that evaporate at brazing temperature contaminate the furnace and the work. Where the process requires it, zinc-free analyses are selected by design.

  • Surface cleanliness. In fluxless furnace work there is no flux to compensate for residue. Rolling lubricant and oxide must be removed at manufacture, not left for the furnace to deal with.

  • Flatness. A foil that curls or waves will trap air between the faying surfaces. Flatness is inspected and reported, not assumed.

  • Handling after arrival. Fingerprints and moisture on foil become defects in the furnace. Packing and handling instructions are part of the supply.

Cutting, Slitting and Shaping Services

  • Slitting to customer width from master coils

  • Cut-to-length sheets sized to the joint footprint

  • Stamped and blanked shapes — discs, washers, frames, annular and irregular profiles — from your drawing

  • Burr-condition and edge-quality control on cut edges

  • Interleaving between sheets on request

Shapes cut from foil double as precision preforms, which is why many buyers use this page and the preform programme together: the alloy stays constant while the geometry changes with each product generation.

Quality Documentation With Each Lot

  • Chemical composition analysis by melt or lot

  • Thickness inspection records against the agreed tolerance

  • Mill test certificate and certificate of conformity

  • Declaration documents supporting RoHS and REACH requirements

  • Traceability from incoming raw material to the packed roll or sheet

Production is controlled under quality-management procedures aligned with the ISO 9001 framework, from material verification through rolling, slitting and inspection to packing.

Packing: Flat, Clean and Sealed

Foil is unforgiving about storage. A pack that lets sheets shift, stick or tarnish undoes the work that went into rolling it. Packing options include:

  • Flat interleaved packs — sheets separated to prevent sticking, marking and scratching

  • Sealed moisture-protected packaging — for vacuum-grade material and long storage periods

  • Coil and spool formats with protective wrap for narrow slit widths

  • Counted-quantity packs — fixed sheets or blanks per pack, matched to line-side consumption

  • Private-label and OEM packaging — your brand, language, part number and barcode

  • Export cartons with moisture protection for sea and air freight

Typical Applications

  • Vacuum devices and electronics — seals, feedthroughs, kovar and copper assemblies, vacuum interrupter components

  • Cutting tools and wear parts — carbide tips and inserts on steel bodies, including layered constructions for expansion mismatch

  • Heat exchangers and thermal assemblies — planar joints across fins, plates and manifolds

  • Sensors and instrumentation — thin-wall and dissimilar-metal joints needing measured alloy volume

  • Optical and precision assemblies — low-distortion joining where excess alloy cannot be tolerated

  • Jewellery, eyewear and decorative hardware — fine joints on visible surfaces

What to Send With Your Enquiry

  1. Alloy grade, or the base metals and service conditions if the grade is open

  2. Thickness, width and format — roll, sheet or stamped shape (a sketch is enough to start)

  3. Heating method — vacuum furnace, atmosphere furnace, induction or torch

  4. Joint gap and face dimensions, where known

  5. Quantity and pack format

  6. Documentation, marking or packaging requirements

Request a Foil Quotation

Send your specification or drawing — PDF, STEP, DXF or a dimensioned sketch. Our engineers confirm a manufacturable thickness tolerance, alloy and packing format, and reply with pricing and lead time.

Silver Brazing Foil — FAQ

What thicknesses are available for silver brazing foil?

Foil can be rolled from approximately 0.05 mm upward, in customer-agreed widths and cut lengths or stamped shapes. Thickness tolerance is confirmed in writing against the contract specification for each order.

Which alloy is used for vacuum furnace brazing foil?

Vacuum and protective-atmosphere work generally uses silver-copper grades such as the Ag72Cu eutectic (BAg-8), which melts at a single temperature and contains no high-vapour-pressure elements. Zinc-free analysis is preferred where volatile elements are not acceptable.

Can foil be stamped into custom shapes?

Yes. Foil can be supplied as full-width rolls, cut-to-length strips, or stamped and blanked into customer-defined profiles based on drawings and agreed contract requirements.

How is silver brazing foil packed?

Foil is supplied flat-packed with interleaving to prevent sticking and marking, in sealed moisture-protected packs. Roll, sheet, counted-quantity and private-label packing formats are all configurable.

How do I choose between foil thicknesses?

Thickness sets the alloy volume per unit of joint area. Thin foil suits close-fitting planar joints and stacked laminations; thicker foil carries more alloy for wider gaps or larger faces. The choice follows joint gap, face area and heating method.

What documentation comes with foil shipments?

Lot chemical analysis, thickness inspection records, a mill test certificate and a certificate of conformity are available with each shipment; RoHS and REACH declaration documents are available on request.


PREVIOUS: No record! NEXT: Silver Brazing Strip