Silver brazing rings — also called preformed brazing rings or silver solder rings — place an exact, pre-measured volume of filler metal exactly where your joint needs it. Instead of hand-feeding wire and hoping each operator measures the same, your line slips a ring onto the fitting, heats the joint, and lets capillary action do the rest. The result: uniform fillets, controlled filler consumption, and far less scrap across thousands of cycles.
We manufacture silver brazing rings in a full span of alloy systems and silver contents, in the diameters, cross-sections, and coil forms your products require — with packaging tailored to your production line or resale needs.
Measured dosing, every cycle. Each ring contains a fixed mass of alloy. Joint strength no longer depends on operator skill or wire-cutting accuracy.
Faster automation. Preformed rings drop directly onto tube-to-socket, flange, and annular joints — a natural fit for flame, induction, and furnace brazing lines running at takt time.
Less alloy waste. No offcuts, no overfeeding, no filler running past the joint. Many users report measurable savings simply by switching from cut wire to rings.
Cleaner, more consistent fillets. Melted alloy follows the capillary gap evenly, producing smooth, continuous joints with fewer porosity and void complaints.
Lower skill dependency. New operators reach qualified-joint quality sooner, and multi-shift consistency improves.
We produce rings across the two principal silver-brazing families, plus specialty grades. All compositions follow AWS A5.8 and GB/T 10046 designations.
Workhorse alloys for copper, brass, steel, and stainless assemblies — including dissimilar-metal joints. Tin-modified grades lower the melting range and improve wetting on stainless steel. Common designations include BAg-5, BAg-6, BAg-7, BAg-24, BAg-36, BAg-37, and their GB/T equivalents. Silver content options: 2%, 5%, 15%, 18%, 25%, 30%, 35%, 40%, 45%, 50%, 56% — or a custom ratio to match your joint requirements.
Self-fluxing on copper-to-copper joints in most conditions, these rings are widely used in HVAC/R heat exchangers, copper valves, fittings, and electrical busbar work. Typical grades: BCuP-2, BCuP-3, BCuP-5, BCuP-6.
For applications demanding narrow melting ranges, controlled-temperature joining, or furnace brazing under protective atmosphere — including pure Ag-Cu eutectic (BAg-8) and lithium-bearing variants for precipitation-hardening steels and thin-wall stainless work.
Not sure which alloy fits? Send us your base metals, joint gap, heating method, and service temperature. Our engineers will recommend a grade and supply samples for line trials.
| Parameter | Range |
|---|---|
| Wire diameter (cross-section) | 0.3 mm – 4.0 mm |
| Ring inner diameter | 2.0 mm and above, per your drawing |
| Silver content | 2% – 72% Ag |
| Ring style | Single-turn, multi-turn (stacked), flat/pressed washer rings |
| Flux options | Bare or flux-cored (pre-fluxed) rings |
| Tolerance | Tight, batch-consistent wire and ID tolerances; full traceability per lot |
Rings are wound, cut, and finished to keep the surface clean and oxide-free — ready to load straight from the box onto your fixtures.
HVAC & refrigeration: copper tubing, evaporators, condensers, suction lines, valve bodies
Automotive: A/C components, fuel lines, hydraulic fittings, sensor housings
Plumbing & sanitary fittings: copper and brass press-fit and sweat joints
Electrical & instruments: busbars, contacts, cable lugs, instrumentation tubing
Oil, gas & hydraulics: high-pressure fittings, couplings, manifold blocks
Hardfacing & tooling: carbide-tip attachment with nickel-modified grades
| Process | How Rings Perform |
|---|---|
| Torch (flame) brazing | Place ring on the joint before heating; heat the parent metal, not the ring |
| Induction brazing | Preload rings for high-volume automated lines; rapid, localized heating |
| Furnace brazing | Bare rings under protective atmosphere; ideal for batch precision work |
| Resistance brazing | Consistent dosing suits electrode-heated repeat joints |
Vacuum or protected melting for low-inclusion alloy with uniform composition throughout each spool and ring
Automated winding and forming for dimensionally stable rings, batch after batch
Lot-level chemical analysis and melting-range verification; certificates (e.g., mill test report) available with every shipment
Production is controlled under quality-management procedures aligned with the ISO 9001 framework, from incoming raw material to finished ring inspection
Tell us how your line or warehouse works, and we match it:
Count-based dispensing: fixed rings per box, bag, or tube for predictable line-side replenishment
Kilogram or gram spools/boxes for consumable distributors
Private-label and OEM packaging with your brand, language, and barcode requirements
Export-grade cartons with moisture protection, suitable for sea and air freight
Mixed-SKU kits (rings + flux) per order if your process uses both
Have a non-standard joint? We manufacture to your drawing:
You send the ring ID, wire diameter, alloy grade, and annual volume
We return a drawing confirmation and sample rings
You validate on your line; we then lock the specification for series supply
Minimum tooling is modest, and repeat orders ship against the frozen spec — so the 500,000th ring joins like the first.
Share your alloy grade (or application description), ring dimensions, and target volume. Our sales engineers reply with pricing, lead time, and — where useful — sample rings for trial.