Foil & Strip

Silver Brazing Strip

  • Flat silver brazing strip made for pre-placed brazing inside fixtures and assemblies. Available in multiple silver alloy grades, these strips can be custom cut to your required width and length for automated and batch brazing operations. Industrial bulk supply from Yiwu Hexin Trading.
  • INQUIRY

Silver Brazing Strip: Filler Metal for Joints That Run Longer Than a Hand Can Feed

Hand-feeding wire works until the seam gets long. Somewhere around the fourth saw segment, the third frame corner, or the metre-long exchanger seam, hand feeding stops being a skill and becomes a lottery — too little alloy in one stretch, too much in the next, and a fillet that varies along its length.

Silver brazing strip solves the problem with geometry. A flat cross-section laid along the seam carries a known volume of alloy per centimetre, places it exactly on the joint line, and stays where it was put while the assembly is fixtured, heated and cooled. We produce strip to customer drawings and agreed contract specifications — any thickness, width and length, any silver content, coiled or cut, packed the way your line consumes it.

Where Strip Sits Among the Other Forms

FormNatural jointWatch out for
Wire and rodShort seams, hand feeding, touch-up workVolume varies with the operator along long seams
StripLong straight or gently curved seams; continuous jointsNeeds a surface to sit against — not for bore-only access
FoilFlat faces and laminationsNot the economical choice for a narrow linear seam
Rings and preformsFixed-geometry repeat jointsTooling per shape; less flexible across product variants

Strip is also the quiet parent material behind many other products: stamped preforms, blanked washers, edge-wound rings and cut shims all start life as strip. Buying strip means buying one alloy in one temper and forming it yourself — or letting us do the forming.

Strip Geometry: Cross-Section Is the Design Variable

For strip, the design variable is the cross-section — thickness × width. It sets the alloy volume per centimetre of seam, and it is the number worth negotiating hardest:

  • Match cross-section to seam length. A seam that is twice as long needs roughly twice the alloy. If the cross-section is fixed by another constraint, plan multiple passes or adjust the layout.

  • Match width to the land available. Strip wider than the flat surface it sits on lifts at the edges and traps air; strip too narrow under-fills the fillet on both sides.

  • Thickness follows the gap. Thin strip suits close clearances and light parts; thick strip carries volume into wider gaps and survives fixturing loads.

  • Account for what flows away. On very long seams, alloy drains toward the heat source if heating is uneven. Wider strip, or strip laid in staggered sections, evens out the distribution.

Send the seam length, joint gap and base metals, and we will propose a cross-section — or confirm the one on your drawing.

Dimensions and Supply Formats

ParameterRange / Basis
ThicknessAny thickness within our rolling range, per contract specification
WidthSlit to customer width per drawing
LengthContinuous coils, spooled lengths, or cut and straightened fixed lengths
Silver content2% – 72% Ag, plus high-purity grades
TemperSoft (annealed) for forming and wrapping; as-rolled where flatness and stiffness matter
EdgeSlit edges, burr condition agreed per specification
SurfaceClean, oxide-free, free of rolling lubricant residue

Coil, Spool or Straight Lengths?

The same strip ships three ways, and the right one depends on how your line handles it:

  • Coils for feeding, winding and converting operations that cut their own lengths

  • Spools for dispensing at the bench or feeding into automated placement

  • Fixed straight lengths sized to one joint — one segment, one frame, one seam — so operators lay rather than measure. This is the format that removes the most variation from manual lines.

Alloy Grades for Strip

Cadmium-Free Ag-Cu-Zn and Ag-Cu-Zn-Sn

The everyday family for copper, brass, steel and stainless seams. Tin-bearing analyses bring the working range down and help the alloy wet stainless steel. Silver contents from 2% to 56%, or a customer-specified analysis under contract.

Silver-Phosphorus (BCuP family)

For copper-to-copper seam work in HVAC/R and electrical products, self-fluxing on copper in most conditions. Supplied where the joint is a long seam rather than a ring joint.

Nickel-Bearing and Vacuum Grades

Nickel-bearing analyses for carbide and stainless strip applications; silver-copper eutectic strip for vacuum and protective-atmosphere furnaces, where the analysis must exclude high-vapour-pressure elements. Compositions are produced to AWS A5.8 / A5.8M, ISO 17672 and GB/T 10046 designations, or to contract-specified analysis.

Edge and Surface Quality — the Part Most Specs Forget

Two strip problems account for most field complaints, and neither appears on a standard datasheet:

  • Burred slit edges. A raised burr holds the strip off the joint face, scratches the parent metal during placement, and carries debris into the gap. Edge burr condition is therefore agreed and inspected per lot, not left to chance.

  • Residual lubricant. Rolling lubricant left on the surface blocks wetting exactly where the alloy needs to flow. Strip is cleaned to a surface that wets on the first pass, and packing is designed to keep it that way.

If your line has ever fought a strip that fed poorly or jointed unevenly, ask suppliers about these two points before comparing prices.

Working Strip on the Line

  • Torch brazing: lay the strip on the seam, flux, and heat the parent metal — the strip shows you when the joint is complete by flowing into the gap

  • Induction brazing: strip placed in the coil's hot zone melts quickly and evenly; fixed-length pieces suit automated placement

  • Furnace brazing: strip is cut, shaped and preloaded into fixtures before the batch enters — the standard route for saw segments and frame assemblies

  • Conversion: strip is stamped, blanked, wound on edge or otherwise formed into preforms; specify temper if the material will be formed after delivery

Quality Documentation With Each Lot

  • Chemical composition analysis by melt or lot

  • Thickness and width inspection records against the agreed tolerances

  • Mill test certificate and certificate of conformity

  • Declaration documents supporting RoHS and REACH requirements

  • Traceability from incoming raw material to the packed coil or bundle

Production is controlled under quality-management procedures aligned with the ISO 9001 framework, from material verification through rolling, slitting, cleaning and inspection to packing.

Packing Matched to Your Line

  • Coil and spool packing with protective wrap, sized for your feeding equipment

  • Straightened cut lengths in counted bundles or trays — fixed pieces per pack for predictable consumption

  • Sealed moisture-protected packs for long storage and vacuum-grade material

  • Private-label and OEM packaging with your brand, language, part number and barcode

  • Export cartons with moisture protection for sea and air freight

Typical Applications

  • Saw and tool manufacture — segment attachment on diamond and carbide saws, band saw blades, core bits

  • Frames and rims — eyewear, spectacle joints, bicycle frames, decorative hardware

  • Heat exchangers and thermal parts — long straight and curved seams on tubes, plates and manifolds

  • HVAC and refrigeration — seam work on copper assemblies where ring geometry does not fit

  • Electrical products — busbar and contact seams, connector assemblies

  • Converting and stamping — strip as feedstock for customer-made preforms, washers and shims

What to Send With Your Enquiry

  1. Alloy grade, or the base metals and service conditions if the grade is open

  2. Thickness, width and temper — or the joint drawing and we will propose them

  3. Supply format: coil, spool or fixed lengths, and the length if fixed

  4. Heating method and joint gap, where known

  5. Quantity and pack format

  6. Documentation, marking or packaging requirements

Request a Strip Quotation

Send your specification or a dimensioned sketch — PDF or DXF both work. Our engineers confirm a manufacturable cross-section, temper and pack format, and reply with pricing and lead time.


Explore the Full Silver Brazing Products Range

Strip is the form for long seams — and the parent material for everything flat. The same silver contents are available in the other forms:

Silver Brazing Strip — FAQ

What is silver brazing strip used for?

Strip is used for long or continuous joints where hand-fed wire gives uneven results — saw segment attachment, frame and rim joints, straight and curved seams — and as the parent material for stamped preforms and edge-wound rings.

How do I choose strip thickness and width?

Cross-section (thickness × width) sets the alloy volume per centimetre of seam. Start from the joint gap and seam length: longer seams and wider gaps need a larger cross-section or multiple passes. The final dimensions are agreed against your drawing.

Which silver contents are available in strip form?

Strip can be produced in silver contents from 2% to 72% Ag, including cadmium-free Ag-Cu-Zn and Ag-Cu-Zn-Sn grades, copper-phosphorus alloys, nickel-bearing grades and vacuum-grade silver-copper, or to a contract-specified analysis.

Do you supply strip in straight lengths as well as coils?

Yes. Strip is supplied as coils, on spools, or cut and straightened into fixed lengths to match your joint layout — for example, segments sized to one saw blade or one frame.

How is strip edge quality controlled?

Slit edges are inspected for burrs and nicks, since a damaged edge can carry contamination into the joint or snag during automated feeding. Edge condition is agreed per specification and checked per lot.

Can silver brazing strip be private-label packed?

Yes. Coils, spools and cut lengths can be packed to your brand, language, part number and barcode requirements, in sealed moisture-protected packaging suitable for export.

PREVIOUS: Silver Brazing Foil NEXT: No record!